diff --git a/ports/stm32/boards/ARDUINO_GIGA/mpconfigboard.h b/ports/stm32/boards/ARDUINO_GIGA/mpconfigboard.h index fdf3128a3606d..cef45d730cc20 100644 --- a/ports/stm32/boards/ARDUINO_GIGA/mpconfigboard.h +++ b/ports/stm32/boards/ARDUINO_GIGA/mpconfigboard.h @@ -32,6 +32,11 @@ typedef unsigned int mp_uint_t; // must be pointer size #define MICROPY_HW_ENTER_BOOTLOADER_VIA_RESET (0) #define MICROPY_HW_TIM_IS_RESERVED(id) (id == 1) +// ROMFS config +#define MICROPY_HW_ROMFS_ENABLE_EXTERNAL_QSPI (1) +#define MICROPY_HW_ROMFS_QSPI_SPIFLASH_OBJ (&spi_bdev.spiflash) +#define MICROPY_HW_ROMFS_ENABLE_PART0 (1) + // Flash storage config #define MICROPY_HW_SPIFLASH_ENABLE_CACHE (1) #define MICROPY_HW_SPIFLASH_SOFT_RESET (1) @@ -125,8 +130,8 @@ void GIGA_board_low_power(int mode); // QSPI flash #1 for storage #define MICROPY_HW_QSPI_PRESCALER (2) // 100MHz #define MICROPY_HW_QSPIFLASH_SIZE_BITS_LOG2 (27) -// Reserve 1MiB at the end for compatibility with alternate firmware that places WiFi blob here. -#define MICROPY_HW_SPIFLASH_SIZE_BITS (120 * 1024 * 1024) +// Reserve 4MiB for romfs and 1MiB for WiFi/BT firmware. +#define MICROPY_HW_SPIFLASH_SIZE_BITS (88 * 1024 * 1024) #define MICROPY_HW_QSPIFLASH_CS (pyb_pin_QSPI2_CS) #define MICROPY_HW_QSPIFLASH_SCK (pyb_pin_QSPI2_CLK) #define MICROPY_HW_QSPIFLASH_IO0 (pyb_pin_QSPI2_D0) diff --git a/ports/stm32/boards/ARDUINO_GIGA/stm32h747.ld b/ports/stm32/boards/ARDUINO_GIGA/stm32h747.ld index 793a76b970292..e7bb950dbe6ce 100644 --- a/ports/stm32/boards/ARDUINO_GIGA/stm32h747.ld +++ b/ports/stm32/boards/ARDUINO_GIGA/stm32h747.ld @@ -13,11 +13,11 @@ MEMORY SRAM3 (xrw) : ORIGIN = 0x30040000, LENGTH = 32K /* SRAM3 D2 */ SRAM4 (xrw) : ORIGIN = 0x38000000, LENGTH = 64K /* SRAM4 D3 */ FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 2048K /* Total available flash */ - FLASH_EXT (rx) : ORIGIN = 0x90000000, LENGTH = 16384K /* 16MBs external QSPI flash */ FLASH_BL (rx) : ORIGIN = 0x08000000, LENGTH = 128K /* Arduino bootloader */ FLASH_FS (r) : ORIGIN = 0x08020000, LENGTH = 128K /* filesystem */ FLASH_TEXT (rx) : ORIGIN = 0x08040000, LENGTH = 1280K /* CM7 firmware */ FLASH_CM4 (rx) : ORIGIN = 0x08180000, LENGTH = 512K /* CM4 firmware */ + FLASH_ROMFS (rx) : ORIGIN = 0x90B00000, LENGTH = 4096K /* romfs partition in QSPI flash */ } /* produce a link error if there is not this amount of RAM for these sections */ @@ -44,6 +44,10 @@ _micropy_hw_internal_flash_storage_ram_cache_end = ORIGIN(DTCM) + LENGTH(DTCM); _micropy_hw_internal_flash_storage_start = ORIGIN(FLASH_FS); _micropy_hw_internal_flash_storage_end = ORIGIN(FLASH_FS) + LENGTH(FLASH_FS); +/* Location of romfs filesystem */ +_micropy_hw_romfs_part0_start = ORIGIN(FLASH_ROMFS); +_micropy_hw_romfs_part0_size = LENGTH(FLASH_ROMFS); + /* OpenAMP shared memory region */ _openamp_shm_region_start = ORIGIN(SRAM4); _openamp_shm_region_end = ORIGIN(SRAM4) + LENGTH(SRAM4); diff --git a/ports/stm32/boards/ARDUINO_NICLA_VISION/mpconfigboard.h b/ports/stm32/boards/ARDUINO_NICLA_VISION/mpconfigboard.h index 505f8b6890169..47bf1be23d460 100644 --- a/ports/stm32/boards/ARDUINO_NICLA_VISION/mpconfigboard.h +++ b/ports/stm32/boards/ARDUINO_NICLA_VISION/mpconfigboard.h @@ -32,6 +32,11 @@ typedef unsigned int mp_uint_t; // must be pointer size #define MICROPY_HW_ENTER_BOOTLOADER_VIA_RESET (0) #define MICROPY_HW_TIM_IS_RESERVED(id) (id == 3) +// ROMFS config +#define MICROPY_HW_ROMFS_ENABLE_EXTERNAL_QSPI (1) +#define MICROPY_HW_ROMFS_QSPI_SPIFLASH_OBJ (&spi_bdev.spiflash) +#define MICROPY_HW_ROMFS_ENABLE_PART0 (1) + // Flash storage config #define MICROPY_HW_SPIFLASH_ENABLE_CACHE (1) #define MICROPY_HW_SPIFLASH_SOFT_RESET (1) @@ -130,8 +135,8 @@ void NICLAV_board_osc_enable(int enable); // QSPI flash for storage #define MICROPY_HW_QSPI_PRESCALER (2) // 100MHz #define MICROPY_HW_QSPIFLASH_SIZE_BITS_LOG2 (27) -// Reserve 1MiB at the end for compatibility with alternate firmware that places WiFi blob here. -#define MICROPY_HW_SPIFLASH_SIZE_BITS (120 * 1024 * 1024) +// Reserve 4MiB for romfs and 1MiB for WiFi/BT firmware. +#define MICROPY_HW_SPIFLASH_SIZE_BITS (88 * 1024 * 1024) #define MICROPY_HW_QSPIFLASH_CS (pyb_pin_QSPI2_CS) #define MICROPY_HW_QSPIFLASH_SCK (pyb_pin_QSPI2_CLK) #define MICROPY_HW_QSPIFLASH_IO0 (pyb_pin_QSPI2_D0) diff --git a/ports/stm32/boards/ARDUINO_NICLA_VISION/stm32h747.ld b/ports/stm32/boards/ARDUINO_NICLA_VISION/stm32h747.ld index 6d6ce279f299c..9bd7f49a8ecaf 100644 --- a/ports/stm32/boards/ARDUINO_NICLA_VISION/stm32h747.ld +++ b/ports/stm32/boards/ARDUINO_NICLA_VISION/stm32h747.ld @@ -13,11 +13,11 @@ MEMORY SRAM3 (xrw) : ORIGIN = 0x30040000, LENGTH = 32K /* SRAM3 D2 */ SRAM4 (xrw) : ORIGIN = 0x38000000, LENGTH = 64K /* SRAM4 D3 */ FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 2048K /* Total available flash */ - FLASH_EXT (rx) : ORIGIN = 0x90000000, LENGTH = 16384K /* 16MBs external QSPI flash */ FLASH_BL (rx) : ORIGIN = 0x08000000, LENGTH = 128K /* Arduino bootloader */ FLASH_FS (r) : ORIGIN = 0x08020000, LENGTH = 128K /* filesystem */ FLASH_TEXT (rx) : ORIGIN = 0x08040000, LENGTH = 1280K /* CM7 firmware */ FLASH_CM4 (rx) : ORIGIN = 0x08180000, LENGTH = 512K /* CM4 firmware */ + FLASH_ROMFS (rx) : ORIGIN = 0x90B00000, LENGTH = 4096K /* romfs partition in QSPI flash */ } _cm4_ram_start = ORIGIN(SRAM4); @@ -46,6 +46,10 @@ _micropy_hw_internal_flash_storage_ram_cache_end = ORIGIN(DTCM) + LENGTH(DTCM); _micropy_hw_internal_flash_storage_start = ORIGIN(FLASH_FS); _micropy_hw_internal_flash_storage_end = ORIGIN(FLASH_FS) + LENGTH(FLASH_FS); +/* Location of romfs filesystem */ +_micropy_hw_romfs_part0_start = ORIGIN(FLASH_ROMFS); +_micropy_hw_romfs_part0_size = LENGTH(FLASH_ROMFS); + /* OpenAMP shared memory region */ _openamp_shm_region_start = ORIGIN(SRAM4); _openamp_shm_region_end = ORIGIN(SRAM4) + LENGTH(SRAM4); diff --git a/ports/stm32/boards/ARDUINO_PORTENTA_H7/mpconfigboard.h b/ports/stm32/boards/ARDUINO_PORTENTA_H7/mpconfigboard.h index 900bf18673728..90a1469056634 100644 --- a/ports/stm32/boards/ARDUINO_PORTENTA_H7/mpconfigboard.h +++ b/ports/stm32/boards/ARDUINO_PORTENTA_H7/mpconfigboard.h @@ -32,6 +32,11 @@ typedef unsigned int mp_uint_t; // must be pointer size #define MICROPY_HW_ENTER_BOOTLOADER_VIA_RESET (0) #define MICROPY_HW_TIM_IS_RESERVED(id) (id == 1) +// ROMFS config +#define MICROPY_HW_ROMFS_ENABLE_EXTERNAL_QSPI (1) +#define MICROPY_HW_ROMFS_QSPI_SPIFLASH_OBJ (&spi_bdev.spiflash) +#define MICROPY_HW_ROMFS_ENABLE_PART0 (1) + // Flash storage config #define MICROPY_HW_SPIFLASH_ENABLE_CACHE (1) #define MICROPY_HW_SPIFLASH_SOFT_RESET (1) @@ -129,8 +134,8 @@ void PORTENTA_board_osc_enable(int enable); // QSPI flash #1 for storage #define MICROPY_HW_QSPI_PRESCALER (2) // 100MHz #define MICROPY_HW_QSPIFLASH_SIZE_BITS_LOG2 (27) -// Reserve 1MiB at the end for compatibility with alternate firmware that places WiFi blob here. -#define MICROPY_HW_SPIFLASH_SIZE_BITS (120 * 1024 * 1024) +// Reserve 4MiB for romfs and 1MiB for WiFi/BT firmware. +#define MICROPY_HW_SPIFLASH_SIZE_BITS (88 * 1024 * 1024) #define MICROPY_HW_QSPIFLASH_CS (pyb_pin_QSPI2_CS) #define MICROPY_HW_QSPIFLASH_SCK (pyb_pin_QSPI2_CLK) #define MICROPY_HW_QSPIFLASH_IO0 (pyb_pin_QSPI2_D0) diff --git a/ports/stm32/boards/ARDUINO_PORTENTA_H7/stm32h747.ld b/ports/stm32/boards/ARDUINO_PORTENTA_H7/stm32h747.ld index 793a76b970292..e7bb950dbe6ce 100644 --- a/ports/stm32/boards/ARDUINO_PORTENTA_H7/stm32h747.ld +++ b/ports/stm32/boards/ARDUINO_PORTENTA_H7/stm32h747.ld @@ -13,11 +13,11 @@ MEMORY SRAM3 (xrw) : ORIGIN = 0x30040000, LENGTH = 32K /* SRAM3 D2 */ SRAM4 (xrw) : ORIGIN = 0x38000000, LENGTH = 64K /* SRAM4 D3 */ FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 2048K /* Total available flash */ - FLASH_EXT (rx) : ORIGIN = 0x90000000, LENGTH = 16384K /* 16MBs external QSPI flash */ FLASH_BL (rx) : ORIGIN = 0x08000000, LENGTH = 128K /* Arduino bootloader */ FLASH_FS (r) : ORIGIN = 0x08020000, LENGTH = 128K /* filesystem */ FLASH_TEXT (rx) : ORIGIN = 0x08040000, LENGTH = 1280K /* CM7 firmware */ FLASH_CM4 (rx) : ORIGIN = 0x08180000, LENGTH = 512K /* CM4 firmware */ + FLASH_ROMFS (rx) : ORIGIN = 0x90B00000, LENGTH = 4096K /* romfs partition in QSPI flash */ } /* produce a link error if there is not this amount of RAM for these sections */ @@ -44,6 +44,10 @@ _micropy_hw_internal_flash_storage_ram_cache_end = ORIGIN(DTCM) + LENGTH(DTCM); _micropy_hw_internal_flash_storage_start = ORIGIN(FLASH_FS); _micropy_hw_internal_flash_storage_end = ORIGIN(FLASH_FS) + LENGTH(FLASH_FS); +/* Location of romfs filesystem */ +_micropy_hw_romfs_part0_start = ORIGIN(FLASH_ROMFS); +_micropy_hw_romfs_part0_size = LENGTH(FLASH_ROMFS); + /* OpenAMP shared memory region */ _openamp_shm_region_start = ORIGIN(SRAM4); _openamp_shm_region_end = ORIGIN(SRAM4) + LENGTH(SRAM4); pFad - Phonifier reborn

Pfad - The Proxy pFad of © 2024 Garber Painting. All rights reserved.

Note: This service is not intended for secure transactions such as banking, social media, email, or purchasing. Use at your own risk. We assume no liability whatsoever for broken pages.


Alternative Proxies:

Alternative Proxy

pFad Proxy

pFad v3 Proxy

pFad v4 Proxy