fix lint

yp05327 · yp05327 · commit 0de9d86f5a75 · 2023-09-15T16:11:02.000+09:00
diff --git a/variants/STM32H7xx/H742Z(G-I)T_H743Z(G-I)T_H747A(G-I)I_H747I(G-I)T_H750ZBT_H753ZIT_H757AII_H757IIT/variant_NUCLEO_H753ZI.h b/variants/STM32H7xx/H742Z(G-I)T_H743Z(G-I)T_H747A(G-I)I_H747I(G-I)T_H750ZBT_H753ZIT_H757AII_H757IIT/variant_NUCLEO_H753ZI.h
@@ -200,58 +200,58 @@
 
 // On-board LED pin number
 #ifndef LED_BUILTIN
-#define LED_BUILTIN           PB0  // LD1
+  #define LED_BUILTIN           PB0  // LD1
 #endif
 #define LED_GREEN               LED_BUILTIN
 #define LED_BLUE              PB7  // LD2
 #define LED_RED                 PB14 // LD3
 
 // On-board user button
 #ifndef USER_BTN
-#define USER_BTN              PC13
+  #define USER_BTN              PC13
 #endif
 
 // Timer Definitions
 // Use TIM6/TIM7 when possible as servo and tone don't need GPIO output pin
 #ifndef TIMER_TONE
-#define TIMER_TONE            TIM6
+  #define TIMER_TONE            TIM6
 #endif
 #ifndef TIMER_SERVO
-#define TIMER_SERVO           TIM7
+  #define TIMER_SERVO           TIM7
 #endif
 
 // UART Definitions
 #ifndef SERIAL_UART_INSTANCE
-#define SERIAL_UART_INSTANCE  3 //Connected to ST-Link
+  #define SERIAL_UART_INSTANCE  3 //Connected to ST-Link
 #endif
 
 // Serial pin used for console (ex: ST-Link)
 // Required by Firmata
 #ifndef PIN_SERIAL_RX
-#define PIN_SERIAL_RX         PD9
+  #define PIN_SERIAL_RX         PD9
 #endif
 #ifndef PIN_SERIAL_TX
-#define PIN_SERIAL_TX         PD8
+  #define PIN_SERIAL_TX         PD8
 #endif
 
 // HSE default value is 25MHz in HAL
 // HSE_BYPASS is 8MHz
 #ifndef HSE_BYPASS_NOT_USED
-#define HSE_VALUE             8000000
+  #define HSE_VALUE             8000000
 #endif
 
 // Extra HAL modules
 #if !defined(HAL_DAC_MODULE_DISABLED)
-#define HAL_DAC_MODULE_ENABLED
+  #define HAL_DAC_MODULE_ENABLED
 #endif
 #if !defined(HAL_ETH_MODULE_DISABLED)
-#define HAL_ETH_MODULE_ENABLED
+  #define HAL_ETH_MODULE_ENABLED
 #endif
 #if !defined(HAL_QSPI_MODULE_DISABLED)
-#define HAL_QSPI_MODULE_ENABLED
+  #define HAL_QSPI_MODULE_ENABLED
 #endif
 #if !defined(HAL_SD_MODULE_DISABLED)
-#define HAL_SD_MODULE_ENABLED
+  #define HAL_SD_MODULE_ENABLED
 #endif
 
 /*----------------------------------------------------------------------------
@@ -274,6 +274,6 @@
   //
   // SERIAL_PORT_HARDWARE_OPEN  Hardware serial ports which are open for use.  Their RX & TX
   //                            pins are NOT connected to anything by default.
-#define SERIAL_PORT_MONITOR     Serial
-#define SERIAL_PORT_HARDWARE    Serial
+  #define SERIAL_PORT_MONITOR     Serial
+  #define SERIAL_PORT_HARDWARE    Serial
 #endif
